ニュース

  • Reasons for uneven color of the oxide film of aluminum material

    Reasons for uneven color of the oxide film of aluminum material

    Three possible causes of aluminum profile oxide film color is not uniform:  (1)When anodized the aluminium profiloe the workpiece area is too large, the swing range in the slot is too large, the edge and the center position and solution contact, update, exchange had large differences, resulting i...
    続きを読む
  • Aluminum profile production process quality control techniques

    Aluminum profile production process quality control techniques

    Aluminum profile production process consists of aluminum ingot casting, and then extruded aluminum billets, and then through the surface treatment, such as: Anodizing, sandblasting and so on, in the specific operation process each process is very important, here we points out some aspects of spec...
    続きを読む
  • How to do the spray cleaning of industrial aluminum profile?

    How to do the spray cleaning of industrial aluminum profile?

    spray cleaning of industrial aluminum profile is widely used, because of complicated equipment, high technical requirements, the cleaning effect is not good, so how to do the cleaning of industrial aluminum profile: 1, Strengthen technological and the implementation of strict operation rules. Ev...
    続きを読む
  • The advantages of broken bridge aluminum window and door

    The advantages of broken bridge aluminum window and door

          Broken bridge aluminum doors                 Broken bridge aluminum  windows Broken bridge aluminum window and door with many advantages, mainly include: reduce the heat-conduction: if adopts the heat insulation break bridge aluminum alloy profiles, the heat transfer coefficient is lower ...
    続きを読む
  • Aluminum alloy decoration

    Aluminum alloy decoration

    The aluminum alloy trim panel has the advantages of light, not burning, durability, convenient construction, good decoration, etc., which is suitable for the decoration of the internal and external walls and cylinders of the public building. In recent years, there are several kinds of aluminum a...
    続きを読む
  • Why use ultrafiltration system in electrophoretic coating process ?

    Why use ultrafiltration system in electrophoretic coating process ?

    Ultrafiltration system of Electrophoresis coating process of the main purpose is to enable the E COAT aluminium is a closed-loop system,  reducing emissions of pollutants, and can also save the electrophoresis coating material. The workpiece after electrophoresis with very low electrical conduct...
    続きを読む
  • Good aluminium tube identification tips

    Good aluminium tube identification tips

    Chinese aluminum tube market prospect is very wide, it also brings bad atmosphere to the entire market, in order to avoid consumer loss, today we taught you a simple four words identification of official tubes and the defective. I. by look and touch The surface of aluminum tube were identified t...
    続きを読む
  • Aluminum shutter process technology

    Aluminum shutter process technology

    Aluminum shutter process technology 1. Leaf blade uses the high quality aluminum alloy materials and processing, with double-sided enamel paint, matched with the fittings and accessories. 2. Up and down track is made of aluminum pressing molding one, coating with 3. Iron head tank, bottom tank ...
    続きを読む
  • Which is better ? aluminium casement window or sliding window

    Which is better ? aluminium casement window or sliding window

    According to the opening mode, Aluminum alloy doors and windows could be  classification two popular kinds: Casement window and sliding window.        aluminium casement window      aluminium sliding window Casement window hinge is installed on the door side inward or outward opening doors and ...
    続きを読む
  • Development trend of high strength aluminum alloy

    Development trend of high strength aluminum alloy

    Development trend of high strength aluminum alloy High strength aluminum alloy is an important lightweight high-strength structural material, which has broad application prospects. The application of aluminum and aluminum alloy is challenged by titanium and titanium alloy and composite materials...
    続きを読む
  • How to improve the strength of the aluminum profile?

    How to improve the strength of the aluminum profile?

    The strengthening of aluminum alloy is mainly to increase its resistance to dislocation action, so there are two ways to strengthen aluminum alloy: liquid treatment and solid state treatment. Liquid treatment is the strengthening of dispersion distribution of carbide, boride and nitride in alum...
    続きを読む
  • Some reasons for the uneven color of the oxide film of aluminum material

    Some reasons for the uneven color of the oxide film of aluminum material

    Three possible causes of aluminum profile oxide film color is not uniform:  (1) when anodized the aluminium profiloe the workpiece area is too large, the swing range in the slot is too large, the edge and the center position and solution contact, update, exchange had large differences, resulting...
    続きを読む
  • Difference of steel, copper and aluminum radiator

    Difference of steel, copper and aluminum radiator

      Copper and aluminum radiator composite takes advantage of the aluminium heat fast , and the corrosion resistance of copper to increase the service life of the radiator, detail good feature of cooper and aluminium radiator as follows: 1、cooper and aluminium radiator with rich colors and...
    続きを読む
  • Attentions when extrusion of 6082 aluminium alloy profiles

    Attentions when extrusion of 6082 aluminium alloy profiles

    (1), aluminum alloy ingot heating A, The line frequency induction heating of aluminum alloy ingot heating, the heat mode with feature as follows. B, extrusion temperature control is accurate, the error is less than ± 3 ℃. If the resistance furnace is heated slowly, will cause the Mg2Si phase pre...
    続きを読む
  • Powder spraying process on the surface of aluminum alloy

    Powder spraying process on the surface of aluminum alloy

    Powder spraying is used to spray powder coating on the surface of the workpiece by spraying powder equipment (electrostatic spray plastic machine). In electrostatic action, the powder will be evenly adsorbed on the surface of the workpiece to form a powdery coating; the powder coating is solidif...
    続きを読む
  • Classification of main products of aluminum alloy

    Classification of main products of aluminum alloy

    Aluminum alloy is one of the most widely used nonferrous metal structural materials in industry. It has been widely used in aviation, aerospace, automobile, mechanical manufacturing, shipbuilding and chemical industry. The main products of aluminum alloy are classified as follows: 1. aluminum al...
    続きを読む
  • Problems and solutions in injection molding process

    Problems and solutions in injection molding process

    Injection molding is a method of industrial product modeling. The products are usually made of rubber injection and plastic injection. Injection molding can also be divided into injection molding and die casting. Shrinkage, shrinkage, non full mold, wool edge, weld mark, silver wire, spray mark,...
    続きを読む
  • Plastic moulds – blow molding

    Plastic moulds – blow molding

    Extrusion blow molding is a method of manufacturing hollow thermoplastic parts. The well known blow objects include bottles, barrels, cans, boxes and containers for all packaged foods, beverages, cosmetics, medicines and daily necessities. Large blow molding containers are usually used for packa...
    続きを読む
  • Welding method of aluminum and aluminum alloy

    Welding method of aluminum and aluminum alloy

    Almost all kinds of welding methods can be used to weld aluminum and aluminum alloys, but the adaptability of aluminum and aluminum alloy to various welding methods is different. All kinds of welding methods have their respective applications, and the following are the more common methods of wel...
    続きを読む
  • The function and basic principle of chemical polishing on aluminum alloy surface

    The function and basic principle of chemical polishing on aluminum alloy surface

    The aluminum alloy workpiece after mechanical polishing has obtained bright surface, but if the workpiece after mechanical polishing is anodized directly, it is only a smooth surface and can not get the film with high reflective coefficient, so the workpiece after mechanically polished must be c...
    続きを読む
  • The function and mode of aluminum alloy connector

    The function and mode of aluminum alloy connector

    Aluminum alloy section connector relates to aluminum alloy profile. A right angle piece, a slot T bolt, an elliptical shim and a nut are arranged on both sides of the right angle piece, and there are two orthogonal elliptical holes on the right angle part, one of which is an elliptical hole for ...
    続きを読む
  • The bolt is actually a large family. What is a T bolt?

    The bolt is actually a large family. What is a T bolt?

    The T bolt is literally understood to be that the shape of the bolt is like a capitalized English letter “T”, which has its reputation. Some T bolts are also called T screw or T type screw. The aluminum alloy profiles are T type bolts and hammerhead bolts. The materials are SUS304 st...
    続きを読む
  • 数値制御レーザ切断機

    数値制御レーザ切断機

      マシンは、CNC切断の切断工程において速度、小さな切断を切断する特性を有します。 産業機械工作機械の設計は、レーザ切断プロセスの高速性と安定性を保証し、異なるパワーでファイバレーザを選択します。 これは、すべての種類をカットし、パンチすることができます...
    続きを読む
  • ラピッドプロトタイピング

    ラピッドプロトタイピング

    また、ラピッドプロトタイピングと呼ばれるAPIDのプロトタイピング技術、(RP技術); 英語:ラピッドプロトタイピング(RPと呼ばれる)、またはラピッドプロトタイピングMANUFACTURING、またはRPM。 自動車業界では、RPのサンプルが呼び出されます。 RP技術が統合され、近代的なCAD / CAMのTEに基づいて開発されて...
    続きを読む
12次へ> >> ページ1/2